A holster mount is a surprisingly consequential piece of hardware. It determines how high or low the pistol sits relative to the belt, how much the holster cants forward or rearward, and whether the entire package stays locked against the body during a draw stroke. The T.REX LINK is a mid-height belt-loop mounting solution designed to solve a specific problem: getting the pistol grip to sit even with the belt line — high enough for a natural draw, low enough to clear chest rigs, plate carriers, and other kit that stacks above the waistline.
The Problem the LINK Solves
The standard approach to mounting an OWB holster on a duty or war belt involves Safariland’s UBL (Universal Belt Loop) paired with the QLS (Quick Locking System) receiver. That combination is well-proven and widely used. However, the UBL positions the holster at a fixed drop that works for some builds but sits too low or too high for others. When you add upper-body equipment — a plate carrier, a chest rig, or even just a load-bearing harness — you need precise control over holster height so the pistol grip is not buried under the cummerbund or dangling at mid-thigh.
The LINK provides that control. Constructed from injection-molded Nylon 6/6, it accepts belts up to two inches wide and includes an adjustable one-wrap keeper to cinch down on thinner belts. The universal hole pattern supports multiple ride heights and permits ±15 degrees of cant adjustment, using the same Ragnarok/Safariland hole pattern that makes it cross-compatible with holsters from T.REX, Safariland, Blackhawk, and other manufacturers sharing that standard. At 2.25 ounces, it adds negligible weight.
Mid-Height Placement and Why It Matters
The term “mid-height” is the defining characteristic. A drop-leg platform pushes the holster down toward the knee — a configuration that creates an awkward draw arc and forces the arm into exaggerated extension when the leg articulates. The war belt overview makes the point bluntly: drop-leg platforms position the holster too low. Conversely, a flush belt-loop that pins the holster body directly to the belt can crowd the grip into the space occupied by plate carrier cummerbunds or mag pouches.
The LINK splits the difference. It keeps the grip approximately even with the belt line — the natural position where the hand falls during a drawstroke without requiring the elbow to chicken-wing outward or the wrist to contort downward. This mid-height placement also leaves room above the holster body for upper-body gear, so the LINK pairs naturally with a full war belt and carrier setup. The result is a clean draw path that remains consistent across standing, kneeling, and movement through doorways.
Mounting, Hardware, and Compatibility
Installation requires mating the LINK to a compatible holster — most commonly the T.REX Ragnarok — using the appropriate hardware. The LINK Hardware Pack (available as a replacement accessory) includes both 8-32 and 10-32 screws in a range of post lengths (.250”, .375”, and .500” for 8-32; .375”, .420”, .500”, and .625” for 10-32), along with washers in .125” and .188” thicknesses. The larger screw heads are specific to the LINK and not interchangeable with standard Ragnarok hardware — a detail worth noting before mixing hardware between mounts. T.REX provides a dedicated LINK installation guide for walk-through instructions.
The universal hole pattern is a quiet but significant design choice. Because the LINK shares the Safariland pattern, it does not lock the user into a proprietary ecosystem. A Ragnarok already running on a UBL/QLS setup can be moved to the LINK for mid-height belt-loop mounting without modification to the holster body. A later switch back to the UBL and QLS system for its tool-less holster swapping capability is equally straightforward, with nothing lost in either direction.
LINK vs. UBL/QLS: When to Use Which
The UBL/QLS combination remains the go-to for users who need to swap holsters rapidly — switching from a Ragnarok configured for a Glock 19 with a TLR-1 to a Ragnarok configured for a P320 with an X300, for example. The QLS fork-and-receiver mechanism allows that exchange in seconds without tools. The UBL also provides a built-in attachment point for a thigh strap, which is strongly recommended for any rigid holster offset from the belt: without it, the holster torques outward during the draw stroke as the belt flexes, causing the pistol to angle into the body and producing an inconsistent draw.
The LINK is the better choice when a simpler, lighter, lower-profile mounting solution is preferred and rapid holster swaps are not required. It sits closer to the body, creates less lateral footprint, and tends to track better during movement because the belt loop keeps the holster firmly indexed to the belt. For users building a dedicated war belt with a single pistol and holster pairing, the LINK often provides a cleaner setup than the UBL/QLS stack.
Broader Mounting Philosophy
The LINK reflects a general design principle visible throughout the T.REX product line: standardized interfaces that allow components to be reconfigured without proprietary lock-in. The same philosophy drives placards that swap between carriers (placard swapping), MOLLE-based pouch attachment (belt mounting solutions), and QD sling attachment points that work across rifles and carriers. A mounting system is not just a bracket — it is the interface layer that determines how quickly and reliably you can configure and deploy your gear. When that interface is universal and well-executed, it compounds across the entire loadout.
For users building their first duty belt, the LINK paired with a Ragnarok is one of the most economical and effective OWB holster mounting solutions available. It gets the pistol where it needs to be, it works with the belts most people already own, and it plays well with the rest of a layered loadout from belt to carrier to chest rig.
Training the Draw
Regardless of mount choice, the draw stroke must be trained until it is automatic. The mid-height placement of the LINK changes the hand path slightly compared to a UBL drop or a concealed IWB draw — the grip is higher and closer to the body, which typically shortens the draw but requires the support hand to clear kit rather than clothing. Dedicated drawstroke development with the specific holster mount in use is essential; gear changes that alter grip height or cant angle invalidate muscle memory built on a different setup.
Products- T.REX LINK — Mid-height belt-loop mount for Ragnarok and other Safariland-pattern holsters. Fits belts up to 2” wide, includes one-wrap keeper for thinner belts, ±15° cant adjustment, Nylon 6/6 construction, 2.25 oz.
- T.REX Replacement Hardware Pack — 8-32 and 10-32 screws in multiple post lengths plus washers in .125” and .188” thicknesses. Note that LINK-specific screw heads are not interchangeable with standard Ragnarok hardware.